Step 5 Once this is done, screw the valve, valve cover and tap handle back into position and replace the handle cap. Step 1 Remove the handle cap to expose the top of the valve. Step 2 Use an adjustable spanner to loosen the valve then remove it. Step 3 Check the ceramic disc valve for damage, grime or wear and clean it or replace it if need be. Step 4 Secure the valve and handle cap back into position.
Step 1 Follow the instructions above to remove the valve depending on your type of tap. Step 2 Remove the worn or damaged O-ring with a screwdriver. Step 3 Roll the replacement O-ring into position and then secure the valve back into position.
Step 1 Use a box spanner to loosen the nut that holds the tap to the sink from below. Step 2 Twist the tap round to give you better access, then use a screwdriver to remove the grub screw.
Step 3 Lift the spout out to give you access to the O-ring, which is the rubber ring at the base of the spout. Step 4 Roll the replacement O-ring into position. Step 5 To replace the spout, line up the marker on the spout with the groove in the tap body and slot the spout back into position.
If your tap is quite old and has recently started to drip, you may be tempted to change the washer but it is worthwhile checking the condition of the valve seat too. A new washer will not be effective if the seat valve is not secure. The valve seat is an essential part of the tap that can corrode and become rough or slightly worn over time.
When it starts to deteriorate it will not create a secure seal and therefore water will escape, causing a leak.
This part should be replaced to ensure a completely water tight seal. If your tap is leaking at the joint of the body, near the handle and spout, this could be due to a loose or damaged spout O ring. To replace an O-ring at the base of a spout you must remove the spout by loosening the grub screw which is usually located at the back of the tap.
Once the spout is released, you can access the O-ring where you can remove the old, worn out o-ring and roll on a new replacement. A leak caused by a worn out washer is one of the most common causes behind a dripping compression washer tap. When you switch on your tap the washer is forced against the valve seat, this constant pressure will eventually cause it to wear out which results in dripping around the spout.
This can be rectified by replacing the washer. If the washer is not installed properly or the replacement washer is the incorrect size the leak will persist. If your tap is beyond repair or in need of an upgrade, we sell an extensive range of taps at Appliance House including modern kitchen taps and traditional style taps. With single lever or dual lever designs on offer along with water filter taps and boiling hot water taps you are sure to find a kitchen tap to suit your needs. September 7, August 27, August 5, Ceramic Cartridge — Similar to the ceramic discs but ceramic cartridges are designed specifically for single monobloc taps.
Why is my tap leaking? The o-ring looks like a bigger washer and is the seal found at the base of the spout. To check and replace it, carefully remove the spout. You will then need to use a flat-head screwdriver to loosen and lift off the o-ring. Slide the replacement o-ring on and put the spout back. Some modern mixer taps including monobloc taps operate with ceramic discs instead of rubber washers, which are hidden inside cartridges within the tap.
There is one cartridge for hot water and another for cold water. If one of the ceramic discs breaks the most common cause for a leaking tap , you will need to replace the whole cartridge. Make sure you buy an exact replacement and follow the steps below.
Cut off your water supply at the stopcock or isolation valve. Run your taps to check the water has stopped. Unscrew the handles of your tap and carefully remove any decorative parts with a flat head screwdriver. This can be easily removed with your flat head screwdriver too. Make sure you know which one is your hot water and which one is your cold water cartridge.
Take out the damaged cartridge and simply pop in a new one. While you wait for expert help, recycle the water from your dripping tap. Collect it in a bowl and use it to water plants, wash dishes and clean with. Share Email Whatsapp Twitter Facebook. Homepage Help and advice Cover How to fix a dripping tap How to fix a dripping tap.
0コメント